Introduction
A UV pass box without HEPA filters is a pass-through chamber used in cleanrooms and controlled environments for transferring materials between areas of different cleanliness levels, equipped with UV lamps for surface decontamination, and it is used in pharmaceutical, biotechnology, and laboratory facilities. The pass box consists of an enclosed chamber with interlocking doors on both sides, so that only one door can be opened at a time, which prevents the direct exchange of air between the two areas and helps to maintain the cleanliness and pressure differential; the UV lamps inside the chamber decontaminate the surfaces of the materials placed in the box, reducing the microbial load on the transferred items, and the interlocking doors and the simple construction provide a physical barrier for material transfer, while the air exchange is limited by the interlocking design, and this type of pass box is used where surface decontamination is the main requirement and where HEPA filtration of the box air is not necessary. UV pass boxes without HEPA filters are used for transferring materials, samples, and equipment into and out of cleanrooms, clean benches, and other controlled areas, and they are used in pharmaceutical, biotechnology, clinical, and research laboratories for transferring items that require surface decontamination, and they are available in various sizes, with features such as UV lamps with timers, interlocking doors, and stainless steel or other cleanable construction. With their decontamination capability and simple design, UV pass boxes without HEPA filters are practical solutions for material transfer with surface decontamination in controlled environments.
UV Pass Box (without HEPA filters) LUP-T2014
UV Pass Box (without filters) is a static type UV pass box equipped UV germicidal lamp, both side electrical interlocked doors, and high quality see through glass window. Pass box is mad...
UV Pass Box (without HEPA filters) LUP-T2015
UV Pass Box (without filters) is a static type UV pass box equipped UV germicidal lamp, both side electrical interlocked doors, and high quality see through glass window. Pass box is mad...
UV Pass Box (without HEPA filters) LUP-T2011
UV Pass Box (without filters) is a static type UV pass box equipped UV germicidal lamp, both side electrical interlocked doors, and high quality see through glass window. Pass box is mad...
UV Pass Box (without HEPA filters) LUP-T2012
UV Pass Box (without filters) is a static type UV pass box equipped UV germicidal lamp, both side electrical interlocked doors, and high quality see through glass window. Pass box is mad...
UV Pass Box (without HEPA filters) LUP-T2013
UV Pass Box (without filters) is a static type UV pass box equipped UV germicidal lamp, both side electrical interlocked doors, and high quality see through glass window. Pass box is mad...
UV Pass Box (without HEPA filters) LUP-T2010
UV Pass Box (without filters) is a static type UV pass box equipped UV germicidal lamp, both side electrical interlocked doors, and high quality see through glass window. Pass box is mad...
Standards
ISO 14644-1-Cleanrooms and associated controlled environments-Classification of air cleanliness by particle concentration
ISO 14644-3-Cleanrooms and associated controlled environments-Test methods
Complies with the above standards, but is not limited to them.
Features
1. UV pass box without HEPA filters for basic material transfer with UV disinfection.
2. UV surface disinfection for transfer between areas with basic contamination control.
3. Suitable for laboratories, clinics, educational and light industrial facilities.
4. Includes pass box chamber, UV lamps, interlocking doors, controller and manual.
5. Supports material transfer with UV surface disinfection without air filtration.
FAQ
Q1: What testing scenarios is this pass box mainly applied to?
A: The UV pass box without HEPA filters is used in general laboratories, clinics, educational institutions, light industrial facilities, research and smaller controlled environments to enable material transfer between areas with UV surface disinfection for basic contamination control without HEPA air filtration. It supports laboratory material and equipment transfer between rooms, clinic and healthcare facility supply transfer, educational laboratory use, light industrial component transfer, research laboratory sample transfer, and basic contamination control applications. The UV disinfection provides surface microbial reduction during transfer, while the interlocking doors prevent direct air exchange between areas, offering a cost-effective solution for basic contamination control where HEPA-level filtration is not required. It is essential for laboratories, clinics, educational, light industrial and research facilities requiring basic material transfer with UV surface disinfection for contamination control, where the UV pass box provides surface microbial reduction and prevents direct air exchange between areas through interlocking doors, offering a cost-effective solution for basic contamination control in general laboratory, clinical, educational and light industrial environments where HEPA-level air filtration is not required but surface disinfection and transfer isolation are beneficial.
Q2: What standards does the pass box comply with?
A: The UV pass box without HEPA filters complies with relevant GB/T standards for laboratory and cleanroom auxiliary equipment, applicable electrical safety standards, and UV radiation safety guidelines. Users should verify compliance with specific facility requirements for their application. The UV dose should be appropriate for the intended disinfection level. For higher-contamination or cleanroom applications, a HEPA-filtered pass box may be required.
Q3: What is the warranty period for the whole machine and key components?
A: The whole pass box is covered by a 12-month warranty. The chamber, doors, interlock, UV system and housing are covered, while UV lamps, gaskets and fuses are consumables or accessories. Damage from improper use or unauthorized repair is excluded. Extended service contracts may be available.
Q4: Is this device difficult to operate? Is professional training required?
A: Operation requires basic training in contamination control, UV safety and pass box operation. We provide an operation manual and remote guidance. Proper material loading, UV cycle setting, door interlock operation and safety procedures are important for effective disinfection and safe operation.
Q5: What is the typical lead-time for order delivery?
A: Standard models require 7-30 working days. In-stock units can ship within 3-7 working days. Custom configurations or large built-to-order systems may require additional time, and we confirm the exact schedule before order confirmation.
Q6: Is regular maintenance required? What is the recommended maintenance cycle?
A: The UV lamp should be replaced every 9 to 12 months, and the door gasket and interlock inspected regularly. The chamber should be cleaned and disinfected per the schedule, and UV intensity verified periodically. A full system performance check should be performed annually.
Q7: Are supporting consumables universal?
A: UV lamps and gaskets are available from specialized suppliers, though system-specific parts should be verified. Long-term consumable cost is low for a basic UV pass box.
Q8: Can I customize parameters or supporting accessories?
A: Customization includes chamber size, material, UV lamp configuration, door type (mechanical/electronic interlock), control features and accessories. Additional lamps and accessories can be ordered separately. Custom orders extend delivery lead-time.
Q9: Does the purchase include on-site installation and commissioning service?
A: Standard delivery includes the UV pass box and operation manual. On-site installation and training are not included for standard orders but can be arranged for facility setup. Remote guidance is provided.
Q10: What types of materials are compatible with this equipment?
A: The UV pass box without HEPA filters transfers materials, equipment, samples and supplies within the chamber size, weight capacity and UV compatibility specification. Materials should be able to withstand UV exposure. Liquids should be in sealed containers. This model does not provide HEPA air filtration, so it is not suitable for high-containment or strict cleanroom applications requiring particulate control. Users should follow proper material loading (not blocking UV), set appropriate UV exposure time, never open both doors simultaneously, never look directly at UV light, replace UV lamps per schedule, and clean the chamber regularly. For applications requiring HEPA-level filtration or higher contamination control, a HEPA-filtered pass box should be selected. The interlock system should be tested periodically. The chamber should be cleaned with appropriate disinfectants, and UV-transparent surfaces should be kept clean for effective disinfection. This pass box is intended for basic transfer and surface disinfection, not for sterile or high-containment material transfer.
Tips: For more details, quotes and customized solutions, please contact us anytime. We’re always ready to serve you professionally.