Introduction
A sulphur content tester is an instrument used to determine the sulfur content of petroleum products, fuels, coal, and other materials, and it is used for quality control, specification compliance, and environmental monitoring in the petroleum, fuel, and energy industries. Sulfur content is an important parameter, since sulfur in fuels contributes to air pollution, such as sulfur dioxide emissions, and damages engines and processing equipment, and regulations limit the sulfur content of fuels; the sulfur content is measured by various methods, including energy-dispersive X-ray fluorescence, in which the sample is irradiated with X-rays and the characteristic fluorescence of sulfur is measured; ultraviolet fluorescence, in which the sample is combusted and the sulfur dioxide produced is measured by UV fluorescence; and other methods, such as combustion and coulometric titration, and the choice of method depends on the sulfur level, the sample type, and the required precision. Sulfur content testers are used in refineries for quality control of gasoline, diesel, jet fuel, and fuel oils; in fuel distribution for verifying compliance with sulfur limits; in coal testing for power generation; in environmental monitoring for emissions assessment; in the petrochemical industry; and in research and testing laboratories, and they are available as benchtop analyzers and portable instruments, with features such as wide measurement ranges, high sensitivity, and compliance with standard test methods, such as ASTM and ISO standards. With their importance in fuel quality and environmental protection, sulfur content testers are essential instruments in the petroleum and energy industries.
UV Fluorescence Sulfur Analyzer LST-T2014
UV Fluorescence Sulfur Analyzer provides a measuring range of 0.2 to 10000mg/L. Utilizes advanced ultraviolet lamp and key components to ensure exceptional sensitivity and operational re...
X-ray Fluorescence Sulfur Analyzer LST-T2013
X-ray Fluorescence Sulfur Analyzer provides a total sulfur measuring range within 7ppm to 5%. It utilizes computerized quantitative analysis based on the principle of X-ray fluorescence ...
Dark Petroleum Products Sulphur Content Tester LST-T2011
Dark Petroleum Products Sulphur Content Tester measures sulphur content from 7 ppm to 5% in various products using minimal standard samples. It integrates electrical, mechanical, and mic...
X-ray Fluorescence Sulfur in Oil Analyzer LST-T2010
X-ray Fluorescence Sulfur in Oil Analyzer offers wide measurement range 0.0050%–5% with 10 ppm detection limit. Employs fluorescence intensity ratio method with automatic correction adj...
Standards
ASTM D4294-Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry
ASTM D2622-Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ISO 8754:2003-Petroleum products-Determination of sulfur content-Energy-dispersive X-ray fluorescence method
Complies with the above standards, but is not limited to them.
Features
1. Sulphur content tester for measuring sulfur in petroleum products and fuels.
2. Multiple methods including XRF, UV fluorescence, bomb and Wickbold for sulfur.
3. Suitable for petroleum refineries, fuel testing, environmental and quality control.
4. Includes measurement system, sample handling, calibration and operation manual.
5. Determines sulfur content affecting emissions, corrosion and fuel quality.
FAQ
Q1: What testing scenarios is this tester mainly applied to?
A: The sulphur content tester is used in petroleum refineries, fuel quality control, environmental monitoring, shipping, power generation, automotive and research institutions to measure the sulfur content of petroleum products, fuels, oils and other hydrocarbons using methods such as X-ray fluorescence (XRF), UV fluorescence, bomb calorimetry or Wickbold combustion. It supports petroleum product specification testing per regulatory limits, fuel sulfur content verification for emissions compliance, lubricant sulfur analysis, environmental monitoring of sulfur emissions, shipping fuel sulfur compliance (IMO 2020 0.5% limit), and research applications. Sulfur content is a critical fuel quality parameter affecting engine emissions, corrosion, catalyst poisoning and regulatory compliance. It is essential for petroleum refineries, fuel testing, environmental, shipping and industrial facilities requiring sulfur content measurement for product specification, regulatory compliance, emissions control, fuel quality, equipment protection and research, where sulfur content is a critical quality and environmental parameter affecting engine emissions, corrosion, catalyst performance, air quality and regulatory compliance in petroleum, fuel, shipping, power and environmental applications requiring accurate sulfur determination per ASTM, ISO and regulatory specifications.
Q2: What standards does the tester comply with?
A: The sulphur content tester follows ASTM D2622 (XRF), ASTM D5453 (UV fluorescence), ASTM D129 (bomb), ISO 20847, ISO 13032, and relevant GB/T standards including GB/T 11140 and GB/T 17040. The apparatus follows applicable safety standards including radiation safety for XRF instruments. Calibration should use certified sulfur reference materials traceable to international standards. Regulatory fuel sulfur limits follow IMO, EPA and applicable national regulations.
Q3: What is the warranty period for the whole machine and key components?
A: The whole tester is covered by a 12-month warranty. The measurement system, detector, sample handling, controller and housing are covered, while sample cups, films, calibration standards and fuses are consumables or accessories. Damage from improper use, radiation exposure (for XRF) or unauthorized repair is excluded. Extended service contracts are available for petroleum testing equipment.
Q4: Is this device difficult to operate? Is professional training required?
A: Operation requires trained petroleum laboratory personnel familiar with sulfur test methods and instrument operation. We provide operation manuals, training and application support. Proper sample preparation, calibration, measurement technique, result calculation and safety procedures (particularly for XRF radiation) are important for accurate sulfur results and safe operation.
Q5: What is the typical lead-time for order delivery?
A: Standard models require 7-30 working days. In-stock units can ship within 3-7 working days. Custom configurations or large built-to-order systems may require additional time, and we confirm the exact schedule before order confirmation.
Q6: Is regular calibration required? What is the recommended calibration cycle?
A: Calibration with certified sulfur reference standards recommended every 3-6 months for regulated testing. Routine verification with a standard before each analytical batch. XRF instruments require radiation safety check per regulations. Sample handling components checked periodically. Full system performance verification annually for accredited laboratories.
Q7: Are supporting consumables universal?
A: Sample cups, films, calibration standards and reagents are available from laboratory suppliers, though instrument-specific parts should be verified. Long-term consumable cost is moderate depending on test volume and method type.
Q8: Can I customize parameters or supporting accessories?
A: Customization includes measurement method (XRF, UV fluorescence, bomb), sulfur range, automation level, sample capacity and data output. Additional accessories and calibration standards can be ordered separately. Custom orders extend delivery lead-time.
Q9: Does the purchase include on-site installation and commissioning service?
A: Standard delivery includes the sulfur tester and accessories with an operation manual. On-site installation, calibration and training are recommended for XRF and UV fluorescence instruments and can be arranged at additional cost. Remote guidance is provided.
Q10: What types of samples are compatible with this equipment?
A: The sulphur content tester measures sulfur in petroleum products, fuels, lubricating oils, residual fuels and other hydrocarbon products within the method range and sample specification. Different methods have different sulfur ranges and sample requirements: XRF for wide range, UV fluorescence for low sulfur, bomb for higher sulfur. Samples should be representative and properly stored. Very volatile samples may require special handling. Users should select the appropriate test method for the expected sulfur range, use certified calibration standards, follow proper sample preparation and handling, ensure proper safety (radiation for XRF, combustion for other methods), and report results with the test method specified for comparison. For regulatory compliance testing, the instrument should be calibrated and maintained per applicable standards, and results should be compared with regulatory fuel sulfur limits (e.g., IMO 0.5%, ULSD 10 ppm or 15 ppm). Quality control samples should be included in each analytical batch for accredited laboratories.
Tips: For more details, quotes and customized solutions, please contact us anytime. We’re always ready to serve you professionally.