Introduction
An oil spectrometer analyzes elemental and chemical properties of oil samples. It is widely used in lubrication and petroleum industries. The system ensures oil quality assessment. It solves slow laboratory analysis methods. By providing spectral detection, it supports maintenance diagnostics.
Oil Spectrometer LSMO-T2011
Oil Spectrometer is used for analysis of electrode oil based on the principle of atomic emission spectroscopy. It mainly consists of a high-energy arc excitation power supply system, whi...
Oil Spectrometer LSMO-T2010
Oil Spectrometer is compact equipment used to measure the elements using the technique of electrode atomic emission spectroscopy. It follows consistent with the requirements of D6595 sta...
Oil Spectrometer LSMO-T2012
Oil Spectrometer is used for the analysis of electrode oil based on the principle of atomic emission spectroscopy. It mainly consists of a high-energy electric arc excitation power suppl...
Oil Spectrometer LSMO-T2011
Oil Spectrometer is compact equipment used to measure the elements using the technique of electrode atomic emission spectroscopy. It takes 30 seconds to test one sample in a single test....
Oil Spectrometer LSMO-T2010
Oil Spectrometer is used for monitoring and evaluating the condition of lubricating oils by detecting metal wear particles, contaminants, and additives. The whole testing and analysis is...
Standards
European Pharmacopoeia 2.2.25-Spectrophotometry, ultraviolet and visible
ASTM E275-08(2022)-Standard Practice for Describing and Measuring Performance of Ultraviolet, Visible, and Near-Infrared Spectrophotometers
Complies with the above standards, but is not limited to them.
Features
1. Quality optical system delivers accurate wavelength and photometric results.
2. Clear digital or software interface simplifies measurement and data handling.
3. Diffraction grating or monochromator provides precise wavelength selection.
4. Wide wavelength range covers common analytical applications.
5. Low stray-light design supports accurate absorbance readings.
FAQ
What is the Oil Spectrometer mainly used for?
The Oil Spectrometer is used to measure absorbance, transmittance or concentration of samples across a defined wavelength range. It supports quantitative analysis, purity checks, kinetics and quality control in chemistry, biology, pharmaceutical and environmental laboratories.
Which standards and regulations apply to the Oil Spectrometer?
The instrument is designed with reference to IEC 61010 electrical safety requirements and relevant GB/T standards for spectrophotometers, including wavelength and photometric accuracy. Procedures should follow applicable standard methods. Compliance documentation can be provided on request.
What warranty comes with the Oil Spectrometer?
The system is covered for 12 months after shipment, including the main mechanism and electrical controls. Replaceable consumables and routine service items are not part of the warranty. Faults caused by improper installation outside the manual or unauthorised modification are not covered.
Will staff need special training?
Routine operation is straightforward and is covered in the user manual, including setup, daily use and basic maintenance. Staff with basic laboratory experience can run it after a short familiarisation. We provide remote guidance and can arrange on-site training where required.
How long does delivery usually take?
Standard models require 7-30 working days. In-stock units can ship within 3-7 working days. Custom configurations or large built-to-order systems may require additional time, and we confirm the exact schedule before order confirmation.
How often should the Oil Spectrometer be calibrated?
The unit is calibrated and tested before delivery. For ongoing accuracy, verify it against traceable reference standards every 6 to 12 months, or according to the laboratory quality schedule. We can arrange calibration service and certificates where required.
Where do we get replacement parts?
The instrument uses standard, widely available consumables rather than special locked items. Replacement parts, accessories and consumables can be ordered from us against the model number. We keep common service parts in stock for prompt supply.
Can it be adapted to our requirements?
Customisation is supported for many installations, including tailored parameters, connections and accessories. Our team reviews the requirement and confirms feasibility and lead time in advance. We avoid committing to options that cannot be delivered reliably.
How is the Oil Spectrometer commissioned?
Most models can be commissioned by following the manual, including positioning, connections, checks and a first test run. Remote guidance is available during start-up. On-site installation, commissioning and training can be arranged separately where required.
What maintenance and safety points matter?
Do not measure highly corrosive or incompatible samples, use dirty cuvettes or skip blank correction. Verify wavelength and photometric accuracy periodically. Follow laboratory safety rules.
Tips: For more details, quotes and customized solutions, please contact us anytime. We’re always ready to serve you professionally.